LASER CLADDED TiCN COATINGS ON THE SURFACE OF TTTANIUM

Laser cladded coatings of TiCN were produced on the surface of titanium. To obtain the optimal techniques, several conditions were tested by varying the laser scanning rate. The choice of shielding gas was also studied. The cladded coatings were then evaluated from the surface mechanics point of view based on their microhardness. The microstructure of some interesting samples was investigated by optical micrographs （OM）. The results showed that under the condition of fixed pulse frequency and pulse width, the laser scanning rate and the shielding gas are the main factors influencing the components of coatings. TiCN coatings were decompounded and oxidized during the cladding process in the condition of no shielding gas of N2. X-ray diffraction results indicated that the composite coatings composed of TiCN, TiC, Ti2N, and TiO2 were produced using appropriate techniques. The results indicated that the best condition in terms of the surface microhardness is obtained when the scanning rate is 1.5mm/s, the pulse frequency is 15Hz, the pulse width is 3.0ms, and N2 is chosen as the shielding gas. The microhardness of the composite coatings is about 1331kg · mm^-2, which is about 4 times that of the substrate. The optical micrographs indicated that the cladding zone is made up of TiCN, TiO2 and some interdendritic Ti, but the diffusion zone mainly consists of the dendrites phase, and the cladded depth is about 80μm, which is more than 2 times that of the laser nitrided sample. There were no microcracks or air bubbles in the cladded sample, which was cladded using the above optimal techniques.     

SAPO-34/SiO_2催化甲醇制烯烃

采用水热法合成了SAPO-34分子筛,并用X射线粉末衍射仪和扫描电子显微镜对SAPO-34分子筛的结构进行了表征,同时探讨了黏合剂种类、甲醇分压、催化剂粒径和硅源等对SAPO-34分子筛催化甲醇制烯烃(MTO)反应性能的影响。实验结果表明,在MTO反应中,三烯(乙烯、丙烯和丁烯)选择性在反应初期存在明显的诱导期;以S iO2为黏合剂合成的SAPO-34/S iO2催化剂不但可缩短MTO反应的诱导期,三烯选择性也较未添加黏合剂或以A l2O3为黏合剂时高1~2个百分点;且当催化剂活性明显下降时,三烯选择性下降的幅度较小。催化剂粒径、甲醇分压及硅源对催化剂的诱导期也有明显的作用。在甲醇分压低于19kPa、催化剂粒径0.25~0.38mm、S iO2为黏合剂、硅酸四乙酯为硅源时,SAPO-34/S iO2催化剂的MTO性能明显提高。     

Optimal Conditions for Preparing Ultra-Fine CeO2 Powders in A Submerged Circulative Impinging Stream Reactor

Cerium carbonate powders were produced in a submerged circulation impinging stream reactor (SCISR) from Ce(NO3)3·6H2O. NH4HCO3 was used as a precipitant in the reaction. Cerium carbonate powders were roasted to produce ultra-fine cerium dioxide (CeO2) powders. The optimal conditions of such production process were obtained by orthogonal and one-factor experiments. The results showed that ultra-fine and narrowly distributed cerium carbonate powders were produced under the optimal flowing conditions. The concentrations of Ce(NO3)3 and NH4HCO3 solutions were 0.25 and 0.3 mol·L-1, respectively. The concentration of PEG4000 added in these two solutions was 4 g·L-1. The stirring ratio, reaction temperature, feeding time, solution pH, reaction time and digestion time were 900 r·min-1, 80 ℃, 20 min, 5～6, 5 min and 1 h, respectively. The final product, CeO2 powders, was obtained by roasting the produced cerium carbonate in air for 3 h at 500 ℃. The finally produced CeO2 powders were torispherical particles with a narrow size distribution of 0.8～2.5 μm. The crystal structure of CeO2 powders belonged to cubic crystal system and its space point group was O5H-FM3M. Under optimal conditions, powders produced by SCISR were finer and more narrowly distributed than that by Stirred Tank Reactor (STR).     

连续运转的掺钛蓝宝石激光器

本文报导一种连续波氩离子激光泵浦的掺钛蓝宝石激光器。在氩离子激光功率(全谱线)为10.45瓦且仅用一组腔镜时,获得最大平均功率超过1000mW、调谐范围750～850nm的掺钛蓝宝石激光输出。     

不同品位高钛渣对沸腾氯化工艺的影响

分别以94％品位高钛渣和90％品位高钛渣为原料，采用沸腾氯化工艺制备粗TiCl4，分析了两种品位高钛渣对沸腾氯化工艺的影响。结果表明：94％品位高钛渣由于其活性低而对沸腾氯化工艺的影响较大。     

Contact interaction of double titanium and chromium diboride with Fe-Cr alloys

The kinetics of wetting double titanium and chromium diboride by iron-based alloys with different chromium content is studied. It is shown that contact angles are formed in such systems over the range 0–10°. The energy parameters of wetting are calculated. It is established that chromium as a surface-active element promotes Fe-Cr alloy spreading on the diboride surface. The microstructure of the interaction area is studied. It is shown that terminal solid solutions and eutectics are formed in the TiCrB₂-(Fe-Cr) system. The optimum compositions of the metallic binder are determined for TiCrB₂-based composite materials. __________ Translated from Poroshkovaya Metallurgiya, Vol. 46, No. 1–2(453), pp. 109–115, 2007     

宝鸡民营钛工业发展现状

介绍了宝鸡民营钛工业在新材料、新技术、新设备、新应用方面的进展,提供了市场需求与发展前景方面的相关信息,并对中小型钛加工企业的发展提出建议。     

Advances in titanium metal injection molding

The approaches to production of titanium powder injection molded parts are reviewed. Historically, oxygen levels have been too high for structural use (particularly with the Ti-6Al-4V alloy). However, recent advances in starting powders, binders and sintering facilities now allow oxygen levels in the Ti-6Al-4V alloy to be controlled to about 0.2 wt.% oxygen. This should result in significant expansion of the titanium PIM market place into aerospace, automobiles, surgical instruments, dentistry, communication devices (such as computers and cell phones), knives and guns. __________ Translated from Poroshkovaya Metallurgiya, Vol. 46, No. 5–6 (455), pp. 118–125, 2007.     

Tribology of nitriding layer, TiN coatings and their complex on AISI D2 steel

The sliding wear and impact wear resistances of D2 steel with nitriding layer, PVD titanium nitride coating and their duplex treatment were investigated. The experimental results suggest that the duplex treatment has the best sliding and impact wear resistances under experimental conditions. And the wear resistance of PVD titanium nitride is better than that of nitriding. The impact wear resistance and wear mechanism of all three surface layers remain unchanged under impact load of 0.2 J or 1 J. All samples end with the same symptom of flaking.